How To Change A Heating Element On A Maytag Dryer Model # Medc200xw1

Maytag Dryer Elements and Burners

Maytag Appliance Parts

Pop Maytag Dryer Elements and Burners

Heating Chemical element - 240V 5400W

PartSelect Number PS334313

Manufacturer Role Number 279838

The heating element (Flat Can Heating Chemical element 5400W, Heating Element, Whirlpool Dryer Heating Chemical element, Dryer Heating Element) provides heat to the dryer. It is metal and measures ten.5 inches long, 7.v inches wide, 2 inches deep. The element attaches to the heater housing. This part can break as a result of wear and tear. This tin can exist material fatigue or prolonged loftier temperature exposure. If broken your clothes may not dry considering of a lack of oestrus. Information technology must exist replaced when at that place is no longer continuity between the terminals. Starting time bank check the thermal fuse on the blower housing before deciding to supervene upon the heating element.

Fixes these symptoms

Rut stays on afterward drum has stopped
No oestrus or not plenty rut
Shuts off too soon
See more...

Installation Instructions

Gadi from Irvine, CA

Dryer motor runs, but no estrus

To accomplish the heating element you simply need to open the back cover of the dryer (about 8 nut-head screws). Remember to disconnect the power.

To remove the heating chemical element at that place are 2 small-scale nut-head screws. Remove the two electric wires. And so you tin pull the heating element away.

You can check the heating element with an ohm-meter or visually inspect it to see if the heating element screw wire is broken.

Don't bustle to dispose the old element. My model includes a small electric condom function. You lot'll demand to transfer it to the new heating element (that comes without it)..

Adept luck.

Dryer Heating Element

PartSelect Number PS11741416

Manufacturer Part Number WP3387747

When connected to electricity the dryer heating chemical element (Metal frame, Metal element ringlet, Ceramic coil insulators) glows red hot and generates oestrus. When air is blown over it, information technology heats the air which is used to dry the clothes. The heating element fits inside the heater housing inside the dryer. Wear and tear on the heater coil from use will eventually crusade the coil to pause and the element to fail. When this office fails it can cease to produce any heat. Alternately, the coil could pause and short to ground assuasive the dryer to continue to heat even when turned off. The latter is a fire gamble and the dryer should be disconnected from power until the chemical element is replaced. If the chemical element coil breaks, the chemical element needs to be replaced. This model is 11 by 5 inches with 5/16" terminals, metal and ceramic, and comes in black. Information technology is sold individually.

Fixes these symptoms

No heat or not enough rut
Takes as well long to dry
As well hot
See more...

Installation Instructions

Alan from Brooksville, FL

Burned out heater element

Remove the kicking plate from the lesser of the dryer past sliding a putty knife along the height border to release the plastic clamps, one on each side about 4" in from the edges. The kick plate folds out and down. You will see the rut shield on the right, held in past one hex head screw. Remove screw and oestrus shield. The element is positioned in an open-front housing and is fastened to the left side of the housing by two hex head screws, located on the "rail" of the element and right near the two wires. Remove the hex-head screws that concur the element in place and disconnected the two wires by pulling them out by hand or with needle nose pliers. The only difficulty here is the cramped working area...I recommend a chubby socket driver for these two screws. Most of this I had to do by feel considering I could non see the screw heads. One time the screws are out and the wires have been disconnected, slide the sometime element straight out toward you. You may need to disconnect a pocket-sized plastic hose located to the left front of the element, just this hose just pulls right off. Vacume the dust & lint build-upwardly out of the whole area, wipe out the element housing and make clean upwardly the whole underside of the dryer prior to installing the new chemical element. Installation is reverse of removal. It also might exist a adept opportunity to make clean out your exhaust duct and the vent to the outside. (Never use the aluminum foil-accordian-type duct.) If the exterior dryer vent has any kind of screen over information technology, remove it and become rid of information technology. Screens collect lint, lint builds upward and burns out elements. Read more...

Dryer Heater Element

PartSelect Number PS11746337

Manufacturer Part Number WP8544771

Fixes these symptoms

No heat or not enough heat
Takes as well long to dry out
Too hot
Encounter more...

Installation Instructions

roberto from houston, TX

My Dryer Was Not Heating Upwards.

I asked for suggest, looked around and priced heating elements and thermostats. This was the best combo offered for the price given. It was shipped and received it very quick. Installed it and 5 minutes later, she was running like a champ! Read more...

Heating Element Connection Wire Kit

PartSelect Number PS334206

Manufacturer Office Number 279457

This kit is used for electric clothes dryers, and it comes with a yellow wire nut.

Fixes these symptoms

No heat or non enough heat
Takes too long to dry
See more...

Installation Instructions

Christopher from dublin, OH

no rut

took a couple differant parts to prepare the dryer. i ordered i part at a time. i was expecting to wait the v days for shipping but i got home from work the next day of odering parts and they were there waiting for me on my doorstep. all three times i ordered. this website is the best site to order parts. i wont go to another website or store if i demand to order parts for appliances. u guys accept my business for life. thumbs up. Read more...

Standard Y-Frame Range Surface Burner

PartSelect Number PS11743366

Manufacturer Office Number WP660532

The standard y-frame surface burner provides heat to your range. If you detect that your element will not heat, you may need to replace your surface burner. This product is vi inches in diameter, and 1500W. The manufacturer suggests replacing the receptacle at the same time that you replace the surface burner. Many of our customers have rated this repair as very piece of cake, and you volition not need whatsoever tools. To complete the repair, simply lift out the quondam burner and replace it with the new ane. Cheque that the burners are turned off before you begin this repair.

Installation Instructions

Laurie from Tequesta, FL

Burner chemical element broke and baste bowls needed to exist replaced.

I went to the local discount mart and bought baste bowls. The ones available at that shop did non fit, and so I decided to buy straight from the stove's manufacturer distributor.

The drip pans were uncomplicated to supersede, as was the new burner element. My old i had bankrupt and was withal working, but I decided to replace it when I ordered the baste pans.

Everything was easy to install and it looks similar a brand new new stove top! I saved a lot of money doing it myself.

Surface Burner - 8 Inch - 2600W

PartSelect Number PS11743367

Manufacturer Office Number WP660533

The surface burner or element on your range provides the heat that you melt with. If your element will not estrus, you may need to replace the surface burner. This surface burner is 8 inches in diameter and 2600 watts. The burner element is made of metallic and has two prongs that connect it to the range. The manufacturer recommends you replace the burner receptacle at the aforementioned time that you supervene upon the surface burner. Many of our customers take rated this repair as very easy. To complete the repair simply lift the old burner up and out, and replace information technology with the new 1. Exist sure to disconnect ability to the range before beginning this repair.

Fixes these symptoms

Chemical element will not heat
Will Not Start
Run into more...

Installation Instructions

Jonathan from Lilburn, GA

viii inch burner wouldn't come on. Wires shorted out

One screw holds the block onto the stove top. Had to clean out fitting for phillips screwdriver or screw would have stripped considering information technology was old with lots of buildup. Even cleaned out, this spiral required nifty strength with phillips screwdriver to keep from stripping. Caution! If you strip information technology, you lot'll have to drill it out! The rest was a snap. Cut the old wires leading to the one-time block (not as well close to where wires disappear into back of stove, though!). Strip insulation off both wires and attach with the connectors that came in the kit. Then button the wires into the block, and finally, attach the cake back to the stove elevation (new screw is supplied). Restore power and everything should be fine. One trouble: Roper/Whirlpool built their appliance in such a way that when the connector block shorts out, it normally takes the infinite switch with it. So I ended up having to go back and buy that switch as well (which just and so happens to cost twice to three times equally much!). If you put it all back together and it still doesn't piece of work, that's probably what happened, so go alee and remove the knob panel and check that switch (it'southward right backside the control knobs on the front). You will probably find a burned connector at the back top left or the switch. Don't forget to write down which wire goes where (or just take a picture of it). Read more...

Liquid Propane Conversion Kit

PartSelect Number PS8691743

Manufacturer Function Number W10606694A

This gas conversion kit is used to convert natural gas burners to liquid propane in dryers. If your dryer will non start, heat, or in that location is an unusual odour, replacing this office can be a solution to the problem. The tools needed for this repair projection are: a putty knife, 5/xvi inch nut driver, pocket-sized flathead screwdriver, pliers, and a three/8 inch wrench. Equally a safety precaution remember to unplug your dryer from the power source before beginning this installation project. Refer to the transmission provided by the manufacturer for further installation instructions and a detailed diagram.

Installation Instructions

Robert from Tenino, WA

converting to LP gas

First I removed the front panel which immune access to the burner assembly. Then I removed the gas connector and elbow from the back of the dryer. So I removed 2 screws that agree burner assembly in place and ii screws that hold an angle caryatid for the burner assembly. Had to loosen the screw that clamps around the gas pipe holding information technology in identify clear in the dorsum inside dryer housing. Unplugged all wiring connectors, and then I removed the burner assembly and removed the 2 screws holding the burner tube to the valve. Remove the orifice and replaced with the proper size for LP gas. Then removed the blocking pin and replaced with i for LP gas. Then reassembled in reverse club. Really pretty piece of cake. Read more...

Heating Chemical element Kit - 240V 4750W

PartSelect Number PS2162280

Manufacturer Part Number LA-1044

This dryer heating chemical element kit is 240 volts and 4750 watts. The role of the heating element is to produce the heat that allows you to dry your clothing during your dryer cycle. If your apparel take too long to dry, or if your dryer is non getting whatever heat or enough heat, you may need to supervene upon your element. Before you lot brainstorm your repair, brand sure to disconnect the power from the dryer. The tools you volition need for this repair include a putty pocketknife, a quarter-inch nut driver, and a pair of needle nose pliers.

Fixes these symptoms

No heat or not enough estrus
Takes likewise long to dry
As well hot
Come across more...

Installation Instructions

Brianna from Littleton, CO

Dry stopped heating - however had skillful air catamenia

I was about to purchase a new dryer because of the age of my dryer and not wanting to hire someone to gear up it. After a niggling web research, I saw several do-it -yourself stories indicating this was a very easy repair.

This was an extremely easy repair and information technology save me lots of $$:
(1) Asunder ability
(2) Opened the top of the dryer
(3) Disconnected wires to temperature sensor.
(4) Used a one/ii" socket wrench with extension and a drill to remove 2 screws holding downward the temperature sensor
(five) Removed 1 screw holding down the heating element.
(six) Removed wires connected to heating element and pulled out old chemical element.
(7) Reassembled new chemical element.
(8) Turned on empty dryer for 30 minutes to burn off scent from the new element.

Worked like a charm!